The following contains excerpts from the book, Electronic Music and Sound Design (Alessandro Cipriani, Maurizio Giri).
This book alternates between teaching concepts of sound design, theoretically, and showing how it is done using Max/MSP. As David Zicarelli, the publisher of Max/MSP, states in the foreword: “This book provides the language for expressing the concepts in terms of the underlying theory (of sound design). Knowing the theory is essential…to be more than someone who can turn a volume knob.”
The book is designed as a college course, presented with software downloads to install into Max/MSP. It states in the Introduction, that for self-learning, the book will require 300 hours of study. Essentially, Max/MSP is a programming language. “The activities in this book that concentrate on replacing parts of algorithms, completing unfinished algorithms, correcting algorithms with bugs, and reverse engineering, have been included in order to pose problems to which the reader is encouraged to find his or her own solutions.”
“Max/MSP is an interactive graphic environment for music, audio processing, and multimedia. It is used through the world by musicians, composers, sound designers, visual artists, and multimedia artists, and it has become a de facto standard for modern technologically-enabled creative projects in both the musical and in the visual spheres. It is a graphical programming language.”
At our Music School in Dallas, Texas we teach our students how to successfully use sound synthesis in their creative work.
Sound Synthesis and Signal Processing
“One might say that while the traditional composer working with traditional instruments composes using sound, the electronic composer composes the sounds themselves.”
“When generating sound using a programming language designed for sound synthesis and signal processing, we specify a desired sound by constructing a ‘virtual machine’ of our own design (realized as an algorithm), and by specifying a series of instructions which this machine will use to create the sound.”
“When the stream of data goes directly to the audio interface as it is processed, so that there are only few milliseconds between the processing and the listening of the synthesized sound, one speaks of realtime synthesis. When the processing of sound is first calculated entirely and saved to an audio file (which can be listened to later) one speaks of non-realtime or offline synthesis.”
“Signal processing is the act of modifying a sound produced by a live source.”
There are three main attributes to sound: frequency, amplitude, and waveform (timbre).
We teach students at our music school in Dallas, Texas how to utilize both signal processing, as well as sound synthesis, to help them develop their ideas.
Frequency
“Frequency is the physical parameter that determines the pitch of a sound…the compressions and expansions…propagate through the air in all directions…density can be expressed as a value called pressure. Once the air is disturbed, the pressure value is no longer constant, but varies from point to point…What has been described is a phenomenon called a cycle, and an event that always repeats in this way is called periodic. The time required to complete a cycle is said to be the period of the wave, which is indicated by the symbol and is measured in seconds (s) or milliseconds (ms). The number of cycles that are completed in a second is defined as frequency, and is measured in hertz (Hz) or cycles per second (cps).”
This is foundational information we teach students in our music school in Dallas, Texas.
“From the instant that it propagates in space, a wave has a length that is inversely proportional to its frequency…This means that a hypothetical wave of 1 Hz would have a length of about 344 meters…A wave of 10 Hz, however, completes 10 cycles in a single second, which fill 344 meters with an arrangement of 10 cycles of 34.4 meters each; each cycle physically occupies a tenth of the total space available. By the same reasoning, a 100 Hz wave has a wavelength of 3.44 meters. We see that frequency decreases with increasing wavelength, and the two quantities are, as we have said, inversely proportional.”
We help students at our music school in Dallas, Texas imagine sound, not in a two-dimensional graph, but as three-dimensional ‘bubbles.’
Amplitude
“Compression corresponds to positive numbers, rarefaction to negative numbers…the number 0 indicates the original stable pressure…Values representing magnitude (or amplitude values) are conventionally expressed as decimal numbers that vary between 0 and 1.”
“Besides using ‘raw’ numbers to represent amplitude, it is also possible to indicate levels by using dB SPL: the symbol dB indicates that the level is to be measured in deciBels, and the acronym SPL stands for Sound Pressure Level. Whereas raw amplitude measurements represent the difference between a sound pressure measurement and some normal pressure, SPL is instead defined as the relationship of a sound pressure at a given moment to a reference pressure (which is typically 0 dB in digital audio). 0dB SPL represents the highest level of accurately reproducible pressure (corresponding to the maximum amplitude), and lower levels are indicated by negative values.”
When students in our music school in Dallas, Texas learn to operate live audio consoles, as well as studio DAWs, their understanding of basic concepts like dB and SPL becomes practical.
“A reduction of 6dB corresponds to a halving of the amplitude, whatever the level may be. This kind of relative measurement is very useful because you can use it while working with sounds of unknown loudness.”
“Here is a useful rule to remember: to reduce the magnitude of a signal by a factor of 10 (in other words, to reduce it to one tenth of the original amplitude) we must reduce the signal by 20 dB. Likewise, to increase a signal tenfold, raise it by 20 dB. It follows that an increase of 40 dB would increase a signal by 100 times, 60 dB by 1000, etc…you are free to define 0 dB as you wish.”
“From the psychoacoustic point of view, the intensity of a sound influences the perception of its pitch…above 2,000 Hz, if we increase the intensity of a sound while maintain fixed frequency, we will perceive that the pitch is rising, while below 1,000 Hz, as intensity increase, there will be a perceived drop in the pitch. On the other hand, frequency also influences our perception of its intensity: the sensitivity of the ear to volume decreases at higher frequencies, increases in the midrange, and decreases greatly at low frequencies. This means that the amplitudes of two sounds must differ, depending on their frequencies, in order to produce the same perceived sensation of intensity. A low sound needs more pressure than is required for a midrange sound to register with the same impact.”
These are all basic understandings of the nature of sound that students at our music school in Dallas, Texas will learn.